ACURA Signal Doctor is a free ham radio signal test: HF transceiver, microphone with stethoscope, spectrum display and a long-distance radio map

Signal Doctor

Signal Doctor is a free ham radio signal test using a real receiver hundreds of miles away. Most hams never hear their own signal. When you ask “How’s my audio?” on the air, people usually say “sounds fine.” As a result, hum, splatter or boomy bass never get mentioned.

Here is how it helps. First, you key up for a few seconds. Next, a public receiver far away records you. Then you get a report card on how your signal sounds and looks out on the band, with a plain fix for anything that needs work. Finally, you can play back your own signal exactly as that receiver heard it.

📍 Showing results for Galloway Township, NJ (FM29)
Works anywhere in the world. Your grid is saved only on this device and is used on every ACURA tool page.

First, check that the grid square above is where your station is. After that, set up your test below.

Not sure what to do? In short, the steps below walk you through the whole test.

How the Ham Radio Signal Test Works

  1. Type your call sign, pick the voice test or the carrier test, and choose a band and a clear frequency.
  2. Press Find receivers. Signal Doctor picks public KiwiSDR receivers at a good distance from your grid square, usually 250 to 800 miles away.
  3. Set your rig to the frequency, listen first, and ask if the frequency is in use.
  4. Press Start test. Stay quiet for 5 seconds while the receiver measures the band noise.
  5. When the box turns red, transmit. For the voice test, talk normally for about 20 seconds and give your call. For the carrier test, hold a steady carrier for about 13 seconds, then unkey and send your call.
  6. Stop when the box turns gray. Your report card, a picture of your signal and a recording of what the far-away receiver heard appear a few seconds later.

What the Voice Test Checks

  • Signal strength: your S-meter reading at the receiver and how far above the band noise you were.
  • Bandwidth: how wide your audio is. Clean SSB is about 2.4 to 2.9 kHz wide.
  • Splatter: whether your signal spills past 3.3 kHz onto the next frequency, the classic sign of too much mic gain, speech processing or an overdriven amplifier.
  • Audio tone: whether you sound boomy, muffled, thin or well balanced.
  • Hum and buzz: 50 or 60 Hz power-line hum riding on your audio, even in the gaps between your words.

What the Carrier Test Checks

  • Frequency accuracy: how many hertz your real signal is from your dial. The receivers are GPS-locked, so this is accurate to a fraction of a hertz.
  • Stability: whether your signal drifts while you are keyed, a sign of a cold rig, a sagging power supply or RF in the shack.
  • Hum on the carrier: hum sidebands 50, 60, 100 or 120 Hz from your carrier, usually from power supply ripple or a ground problem.

Good Operating Practice

  • First of all, only transmit where your license allows, and always give your call sign.
  • Pick a clear frequency, listen first, and ask “Is this frequency in use?” before you start.
  • Also, low power is fine. 5 to 100 watts is plenty for the test.
  • Above all, keep it short. Each test is 30 seconds, and only about 20 of that is transmitting.
  • For the carrier test, use the CW portion of the band and keep the power low.

Ham Radio Signal Test FAQ

Is this a real ham radio signal test, or a simulation?
It is really you. In fact, Signal Doctor connects to a real public KiwiSDR receiver, records exactly what it hears on your frequency, and grades that recording. You can play it back on the report card.

Why did it say the receiver did not hear me?
In most cases, the band is not open between you and that receiver at that moment, or the rig was on the wrong frequency or sideband. So, try another receiver from the list. For example, higher bands (20 meters and up) usually work best in daylight; 40 and 80 meters work best late afternoon and at night.

Why did the test stop early?
Some receiver owners limit how long outside visitors can stay connected, and some fill up with listeners. In that case, just pick another receiver and run the test again.

Can the receiver tell me about my antenna?
Signal strength tells you how well you are getting out in that direction. However, it does not show your whole pattern. For a full picture of where your antenna sends your signal, try the Antenna Report Card.

Who runs the receivers?
The receivers are public KiwiSDRs run by hams and radio listeners around the world. Signal Doctor uses one channel for about 30 seconds per test and identifies itself as ACURA Signal Doctor in the receiver’s user list. Finally, thank you to everyone who shares a receiver with the ham community.

Related Tools

RFI Detective · Antenna Report Card · Listen on the ACURA SDR Receiver · Ionosphere Heartbeat · Best Band Right Now